[PRE TASK PLAN TITLE]

Project: [PROJECT NAME]

Date: 2025-08-12

Location: [LOCATION]

Supervisor: [SUPERVISOR NAME]

Task Overview

This pre-task plan outlines the safety procedures for operating a drill press when drilling plastic materials. It addresses hazards such as flying debris, entanglement, and machine malfunction to ensure a safe working environment.

Expected Duration: 4 hours

Number of Workers: 1

Required PPE and Equipment

Personal Protective Equipment

• Safety Glasses/Face Shield: CSA-certified eye and face protectors are required to protect against flying debris. [1]
• Gloves (appropriate for plastic handling): To protect hands from sharp edges and potential cuts.
• Close-fitting clothing: To prevent loose clothing from getting caught in the drill press.
• Safety Boots: Required to protect feet from falling objects and sharp plastic debris.

Tools and Equipment

• Clamps or Drill Vise: Used to securely hold the plastic workpiece in place during drilling. [1]
• Drill Bits (appropriate for plastics): Used for drilling holes in plastic materials. Ensure the bit is sharp and appropriate for plastic.
• Brush or Vacuum: Used to remove plastic chips and debris from the work area. [1]
• Measuring Tools (Ruler, Calipers): Used to accurately measure and mark the drilling location on the plastic workpiece.

Hazard Analysis

Identified Hazards

Hazard	Risk Level	Potential Consequences
Flying plastic debris during drilling.	Medium	Eye injuries, skin lacerations, and potential for infection.
Entanglement of loose clothing or hair in the rotating drill bit.	High	Serious injury, including fractures, lacerations, or amputation.
Drill press malfunction (e.g., motor failure, chuck failure).	Medium	Equipment damage, potential for projectile hazards, electrical shock.
Sharp edges on plastic materials and drilled holes.	Low	Cuts, lacerations, and puncture wounds.
Dust inhalation from drilling plastic.	Low	Respiratory irritation, potential long-term health effects.

Control Measures

• Ensure the face shield or safety glasses are in good condition and fit properly.: Always wear CSA-certified eye and face protectors to shield eyes from flying debris. [1]
• Ensure the clamp or vise is properly tightened before starting the drill press.: Secure the workpiece using clamps or a drill vise to prevent spinning. [1]
• Visually inspect the guards for damage and ensure they are properly positioned.: Ensure all guards and shields are in place and functioning correctly before operating the drill press. [1]
• When making deep holes, clean out the hole frequently.: Remove burrs and chips from a drilled hole. [1]
• Do not use compressed air, as it can cause debris to become airborne.: Use a brush or vacuum to remove plastic cuttings and debris from the work area. [1]
• This action prevents the drill from pulling into the work and breaking.: Reduce the drilling pressure when the drill begins to break through the workpiece. [2]

Emergency Procedures

Emergency Contact Information

• Site Emergency: 911
• First Aid: On-site First Aid Station
• Supervisor: Supervisor's Name and Number

Emergency Response Steps

1. Immediately stop the drill press.
2. Provide first aid and call for medical assistance if necessary.
3. Report the incident to the supervisor.
4. Investigate the cause of the incident and implement corrective actions to prevent recurrence.

Evacuation Routes

Evacuate through the nearest marked exit and proceed to the assembly point.

Designated assembly point outside the building.

Required Permits and Certifications

• Drill Press Operation Certification
• Lockout/Tagout Certification (if maintenance is required)

Additional Safety Considerations

• Ensure adequate ventilation to minimize dust inhalation.
• Inspect the drill press before each use to ensure it is in good working condition.
• Keep the floor around the drill press free of oil and grease. [2]
• Never leave the drill press running unattended. [3]

Pre-Task Plan Verification

By signing below, you acknowledge that you have reviewed and understand this pre-task safety plan:

Supervisor: _________________________ Date: __________

Safety Representative: _________________________ Date: __________

Workers:

1. Name: _________________________ Signature: _________________________ Date: __________
2. Name: _________________________ Signature: _________________________ Date: __________
3. Name: _________________________ Signature: _________________________ Date: __________

This pre-task plan must be reviewed and updated if conditions or scope of work changes.

Safety powered by SALUS